1421060 truck leaf spring air suspension part leaf spring

Short Description:

Part NO. 1421060 JC NO. JCBHZD0142
Spec. 100*47/45(mm) Model Scania
Material 52CrMoV4 MOQ 50 SETS
Port Shanghai/Xiamen/Ningbo Payment T/T,L/C,D/P
Lead Time 20-30 days Warranty Warranty

Product Detail

Product Tags

Spring Measurements Specs

Totally 2 blades ,2pcs pad among blades , the 1st blade Width(mm)*Thickness(mm): 100*47, the 2nd blade Width(mm)*Thickness(mm): 100*45, the 1st Measurement 745 mm (Free Length Measurement),the 2nd Measurement 1125 mm (Free Length Measurement) , Tolerance range within ±2mm . 1pc composite  bush Ø30*Ø68*121 comes to install spring eyes .

All datas are obtained by measuring the new produce product .



All Scania models till start of 5-series 2005 onward ,have a simple index system ,the first letter of the far left side(as known as prefix) is the cab type:G(rigidly mounted short,low cab),P(suspended low cab,short or long),R(high cab,short or long),and T(bonneted cab,short or long).Then first one or two digits indicate engine size(e.g.8,11,or 14 liter engine.denotes 82,112/111/110,or 144)and the last number before letter suffixes points out the series which are as followings:0-series(110 and 140 produced 1968-1974),1-series(111 and 141 produced 1974-1981),2-series(82,92,112 and 142 produced 1981-1988)3 series:93,113,143(1987-1995) and finally 4-series(94,114,124,144 and 164 produced 1995-2004).at the end letter suffixes(far right side)M,H,or E,relate to frame/suspension ratings-”medium”,”heavy”,or”extra-heavy”duty.In some models further codes like L,D,C and G were used compared to other to describe the chassistypes .

Finished Products Photos


Key Points Keep The High Quality

1) Raw matrail .
Thickness less than 20mm. we choose SUP9/55Cr3/SAE5160H as the product material
Thickness from 20-30mm. wE choose SUP11A/50CrVA
Thickness more than 30mm. We choose 51CrV4 as the raw material
Thickness more than 50mm. We choose 52CrMoV4 as the raw material
2) Quchenging Process
We strickly controled the steel temeprure around 800 degree.
we swing the spring in the qenching oil among 10 seconds according to the spring thickness.
3)Shot Peening.
Each assmembing spring set under stress peening .
Fatigue test can reach over 150000 cycus
4) Painting
Each leaf under cataphoresis painting.
Salt spray testing reach 500hours

Production Process


1.Material Cutting


4.Edge Cutting


7.Stress Peening








3.Eye Rolling






Q1: What type of leaf spring could you produce ?

A: We can produce most kinds of springs in the market. especially on the parabolic springs.

Q2: What material could you supply for leaf spring?

A: Our material grade should be SUP9/SUP9A /SUP11A/51CrV4 /52CrMoV4/ even 55Cr3 and  SAE5160H as well .

Q3: How long will be your delivery time?

A: 20-40days. If material stock enough around 20days. if not,would be 40days

Q4: What payment terms are acceptable?

A: TT and LC at sight

Q5: What is the packing?

A: No fumigation wooden pallet . we also can pack according to whatever you request if reasonable.

Q6:How about the surface finishing ?

A : electrophoresis coating (black,red,gray,or as customer’s requests )

  • Previous:
  • Next: