2020 High quality Spring Leaf - TRA-2740 Trailer part leaf spring parabolic leaf springr – Jiachuang

Short Description:

Product Detail

Product Tags

Feedback (2)

To become the stage of realizing dreams of our employees! To build a happier, much more united and far more professional team! To reach a mutual profit of our clients, suppliers, the society and ourselves for ISUZU NPR/700P Leaf Spring , Rubber Mount , U Shaped Bolt Clamp , We warmly welcome mates from all walks of life to hunt mutual cooperation and develop a more good and splendid tomorrow.

2020 High quality Spring Leaf - TRA-2740 Trailer part leaf spring parabolic leaf springr – Jiachuang Detail:

This spring assy are widely used in American for trailer .

Spring Measurements Specs

Totally 3 blades , 3pcs middle pads , End to End Measurement 1159 mm (Free Length Measurement), Tolerance range ±6mm ,A side Free Arch Measurement 146mm，Tolerance range ±6mm ,B side Free Arch Measurement 132mm,Tolerance range +6mm, Middle straight 203mm .

All datas are obtained by measuring the new produce product .

tuzhi

Parabolic Tra2740 Leaf Spring Are Made As Follows

Multi-leaf springs are made as follows:

1. Shearing of flatbar

2. Center holepunching / Drilling

3. End Heatingprocess forming (hot & cold process)

1. Eye Forming /Wrapper Forming

2. Diamond cutting/ end trimming / width cutting / end tapering

3. End punching /end grooving / end bending / end forging / eye grinding / end rolling

4. Center holepunching / Drilling / nibbing

4. Heat Treatment

1. Heating

2. Hardening

3. Cambering

4. Quenching

5. Tempering

5. Surfacepreparation

1. Shot peening /stress peening

2. Primary painting

6. Eye bushpreparation process

1. Eye reaming /eye boring

2. Bush insertion

3. Bush reaming

7. Assemble

1. Presetting &load testing

2. Finish painting

3. Marking &packing

TRA Leaf Spring Characteristics

1. The TRA LEAF SPRING acts as a linkage for holding the axle in position and thus separate linkages are not

necessary. It makes the construction of the suspension simple and strong.

2. Because the positioning of the axle is carried out by the leaf springs, it is disadvantageous to use soft springs

i.e. springs with low spring constant.

3. Therefore, this type of suspension does not provide good riding comfort. The inter-leaf friction between the leaf

springs affects the riding comfort.

4. Acceleration and braking torque cause wind-up and vibration. Also wind-up causes rear-end squat and nose-

diving.

5. The inter-leaf friction damps the spring’s motion and reduces rebound, which until shock absorbers were widely

adopted was a great advantage over helical springs.

Key Points Keep The High Quality

1) Raw matrail .

Thickness less than 20mm. we choose SUP9/55Cr3/SAE5160H as the product material

Thickness from 20-30mm. wE choose SUP11A/50CrVA

Thickness more than 30mm. We choose 51CrV4 as the raw material

Thickness more than 50mm. We choose 52CrMoV4 as the raw material

2) Quchenging Process

We strickly controled the steel temeprure around 800 degree.

we swing the spring in the qenching oil among 10 seconds according to the spring thickness.

3)Shot Peening.

Each assmembing spring set under stress peening .

Fatigue test can reach over 150000 cycus

4) Painting

Each leaf under cataphoresis painting.

Salt spray testing reach 500hours

Production Process

material-cutting

1.Material Cutting

Edge-Cutting

4.Edge Cutting

Stress-Peening

7.Stress Peening

Punching

2.Punching

Quenching

5.Quenching

Assembling

8.Assembling

Eye-Rolling

3.Eye Rolling

Tempering

6.Tempering

Painting

9.Painting

FAQ

Q1: What type of leaf spring could you produce ?

A: We can produce most kinds of springs in the market. especially on the parabolic springs.

Q2: What material could you supply for leaf spring?

A: Our material grade should be SUP9/SUP9A /SUP11A/51CrV4 /52CrMoV4/ even 55Cr3 and SAE5160H as well .

Q3: How long will be your delivery time?

A: 20-40days. If material stock enough around 20days. if not,would be 40days

Q4: What payment terms are acceptable?

A: TT and LC at sight

Q5: What is the packing?

A: No fumigation wooden pallet . we also can pack according to whatever you request if reasonable.

Q6:How about the surface finishing ?

A : electrophoresis coating (black,red,gray,or as customer’s requests )

Product detail pictures:

Related Product Guide:

We have now our possess revenue group, design staff, technical crew, QC team and package group. We now have strict excellent regulate procedures for each process. Also, all of our workers are experienced in printing subject for 2020 High quality Spring Leaf - TRA-2740 Trailer part leaf spring parabolic leaf springr – Jiachuang, The product will supply to all over the world, such as: Muscat, French, Kuwait, For anyone who is keen on any of our goods right after you view our product list, please really feel absolutely free to get in touch with us for inquiries. You are able to send us emails and contact us for consultation and we shall respond to you as soon as we can. If it's easy, you may locate out our address in our web-site and come to our business for far more information of our products by your self. We are always ready to construct extended and steady co-operation relations with any possible customers in the related fields.

BPW Cranked Single trailing Arms